18 Years Factory offer Various kinds of Industrial Brushes for Algeria Factories

https://www.beadaholique.com/jewelry-making-tools/measuring-design – Create personalized message bracelets with metal punches and the EZ-Bender tool. This video also shows how to add patina to the lettering to make it really stand out.

Designer: Julie Bean

Related Project:

To Be or Not to Be Bracelet
Project B731

https://www.beadaholique.com/to-be-or-not-to-be-bracelet.html

You can find the supplies in this video at Beadaholique.com

Beadsmith 27 Piece Uppercase Calligraphy Alphabet Letters Punch Set For Metal 3mm
SKU: XTL-0756

https://www.beadaholique.com/beadsmith-27-piece-uppercase-calligraphy-alphabet-letters-punch-set-for-metal-3mm.html

BeadSmith Bracelet Stamping Strip, For Altered Jewelry 0.25×6 Inches, 2 Pieces, Copper
SKU: PND-0474

https://www.beadaholique.com/beadsmith-bracelet-stamping-strip-for-altered-jewelry-0-25×6-inches-2-pieces-copper.html

BeadSmith Metal Elements EZ-Bender, Cuff Bracelet Tool, Steel
SKU: XTL-1063

https://www.beadaholique.com/beadsmith-metal-elements-ez-bender-cuff-bracelet-tool-steel.html

Vintaj Patina Opaque Permanent Ink – Black Onyx – 0.5 Ounce Bottle
SKU: XTL-9078

https://www.beadaholique.com/vintaj-patina-opaque-permanent-ink-black-onyx-0-5-ounce-bottle.html

Eurotool Bench Block Helper – Rubber Base With Interchangeable Steel And Nylon Blocks
SKU: XTL-0250

https://www.beadaholique.com/eurotool-bench-block-helper-rubber-base-with-interchangeable-steel-and-nylon-blocks.html

ImpressArt Brass Hammer For Metal Stamping – 1 Pound – 1 Piece
SKU: XTL-0277

https://www.beadaholique.com/impressart-brass-hammer-for-metal-stamping-1-pound-1-piece.html

BeadSmith Bracelet Bending Pliers – Gently Curve Bracelets And Components
SKU: XTL-0084

https://www.beadaholique.com/beadsmith-bracelet-bending-pliers-gently-curve-bracelets-and-components.html

BeadSmith Bracelet Stamping Strip, For Altered Jewelry 0.25×6 Inches, 2 Pieces, Brass
SKU: PND-0470

https://www.beadaholique.com/beadsmith-bracelet-stamping-strip-for-altered-jewelry-0-25×6-inches-2-pieces-brass.html

BeadSmith Bracelet Stamping Strip, For Altered Jewelry 0.25×6 Inches, 2 Pieces, Silver Tone Nickel
SKU: PND-0478

https://www.beadaholique.com/beadsmith-bracelet-stamping-strip-for-altered-jewelry-0-25×6-inches-2-pieces-silver-tone-nickel.html

My 2016 S1000RR with only 2000km created a small oil leak from the output shaft seal. The bike is still under warranty from BMW Motorrad Canada, but I decided to pay for the part ($40cdn) and change the seals myself. I don’t have the time to get my trailer, and deliver the bike to the dealer, and pick it up the next day.

The output shaft seal part comes with three items. Outer dust seal, inner metal sleeve, and a “o ring” rubber seal. The oil leak is most likely caused from the “o ring” seal not in proper position, or ripped.

I removed the outer dust seal by using a sharp punch and hammered a small hole into the dust seal. I then used a wood screw to screw into the hole to create a grab handle. Using locking pliers, I was able to pull it out with one large yank.

With the dust seal removed, I noticed the inner sleeve was also stuck, but after a few hand turns, it came free. The “o ring” seal behind it was still in tact, so it must have been leaking due to a miss-install by the factory. The “o ring” can get squished, or not seat properly with the metal sleeve.

I don’t have a BMW manual (not sure anyone does), so I had to figure out the best method to reinstall the new rubber gasket, sleeve, and outer dust seal.

Let me know if you have any questions in the comment section.

Marcel Irnie
https://youtube.com/irnieracing (my main Youtube Channel)
https://fb.com/superbikeracer (FB Athlete Page)
https://fb.com/wbmotors (World’s Best Motorcycles)