Manufacturing Companies for 10-PCS Hex Key Sets packaged by spring ring for America Importers

Video tutorial on how to cut a single ear or double ear crimp style hose clamp. I do show a couple different methods in this tutorial, each method will be dependant if you have the tools on hand. If you plan on using the high speed rotary tool method, DO NOT USE it on flammable fluids, this does create some heat, as well as sparks which could cause a fire. These crimp clamps are only intended to be for one time usage, once cut they cannot be removed again. They can be found on a variety of applications such as vacuum lines, coolant lines, fuel lines, hydraulic lines, washer fluid lines, etc.

Website: https://4diyers.com
Facebook: https://www.facebook.com/4diyers
Google Plus: https://plus.google.com/+4DIYers
Twitter: https://twitter.com/4DIYers
Instagram: https://www.instagram.com/4diyers/
Tumblr: https://4diyers.tumblr.com
Pintrest: https://www.pinterest.com/4diyers/

Tools/Supplies Needed:
-bullnose pliers/end-cutting pliers
-side cutters/diagonal cutting pliers
-high speed rotary tool/Dremel
-arbor with abrasive cutting disk
-safety glasses
-gloves

Procedure:
-in order to remove this style of clamp, it does have to be cut to release the tension and be remove
-the ear can be mechanically cut by using the specific tool intended for these clamps or using a pair of bullnose pliers/end-cutting pliers or side cutters/diagonal cutting pliers can be used to cut the ear
-if you are limited for room, do not have leverage required to cut it, or are having trouble cutting it in general you can use a high speed rotary tool with an abrasive cutting disk
-I do not recommend using the high speed rotary tool with an abrasive cutting disk on flammable fluids
-be sure to wear safety glasses when using this method, gloves are also great protection as well
-once the ear is cut using either method, even a double ear crimp clamp only requires one ear to be cut, the clamp can be spread open
-you can either bend the clamp open and remove the clamp, or slide the clamp back
-now you can remove the hose off the fitting

Thank you to all those who watch my videos and support my content. Don’t forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

This video provides step-by-step repair instructions for replacing the air vane on a Briggs and Stratton small engine. The most common reasons for replacing the air vane are when replacing the air vane or when performing engine maintenance.

Click here to purchase part #790848:

https://www.repairclinic.com/PartDetail/Air-Scoop/790848/1646703?TLSID=1876

Additional small engine repair, troubleshooting tips, help with finding your model number and part replacement videos can be found on our website:

https://www.repairclinic.com/RepairHelp/Small-Engine-Repair-Help?TLSID=1876

All of the information for this air vane replacement video is applicable to the following brands:
Briggs & Stratton, Toro, John Deere, Lawn Boy

Tools needed: Phillips-head screwdriver, 5/16th inch socket or nut driver, 3/8th inch socket or nut driver, pliers, ¼ inch socket or nut driver

Connect With Us!

https://plus.google.com/+repairclinic

https://www.facebook.com/RepairClinic

https://www.twitter.com/RepairClinic

https://pinterest.com/RepairClinic/

Join our free VIP email list for discounts and money-saving tips: https://tinyurl.com/pnnh3be
Check out our blog: https://www.DIY.RepairClinic.com

Don’t forget to like and comment on this video, and subscribe to our channel!